WebSocket to WebSocket Integration using Subprotocols

If you need to read and transform the content of WebSocket frames, the information in incoming WebSocket frames is not sufficient because the WebSocket protocol does not specify any information about the content-type of frames that flow through WebSocket channels. Hence, the ESB Profile of WSO2 Enterprise Integrator (WSO2 EI) supports a WebSocket subprotocol extension to determine the content type of WebSocket frames.

The WebSocket inbound endpoint of the ESB Profile supports the following Synapse subprotocols by default:

synapse(contentType='application/json')
synapse(contentType='application/xml')
synapse(contentType='text/xml')

Now let's look at a sample scenario that demonstrates WebSocket to WebSocket integration using subprotocols to support content handling.

This scenario includes the following sections:

Introduction

Let's say you need to send messages between two WebSocket based systems using the ESB Profile of WSO2 EI as a WebSocket gateway that facilitates the messaging. Let's also assume that you need to read and transform the content of WebSocket frames that are sent and received.

The following should take place in this scenario:

The WebSocket Client sends WebSocket frames to the ESB Profile of WSO2 EI.
When the initial handshake happens between the WebSocket client and the WebSocket inbound endpoint of the ESB Profile, the WebSocket client sends a Sec-WebSockets-Protocol header that specifies the content type of the WebSocket frame. In this sample it is synapse(contentType='application/json').
The WebSocket inbound endpoint of the ESB Profile determines the content-type of the incoming WebSocket frame using the subprotocol.
Once the handshake is complete, the WebSocket inbound endpoint builds all the subsequent WebSocket frames based on the content-type specified during the initial handshake.
The ESB Profile of WSO2 EI sends the transformed message in the form of WebSocket frames.

If necessary, you can use the data mapper to perform data transformation inside the ESB message flow. For example, you can perform JSON to JSON transformation. To do this, you have to explicitly apply the required data mapping logic for all WebSocket frames.

Prerequisites

Start the ESB Profile of WSO2 EI. For information on how to start the ESB Profile of WSO2 Enterprise Integrator, see Running the Product.
Download the netty artifacts.
Open a terminal, navigate to the location where you saved the netty artifacts, and execute the following command to start the WebSocket server on port 8082:
```
java -cp netty-example-4.0.30.Final.jar:lib/*:. io.netty.example.http.websocketx.server.WebSocketServer
```

Configuring the sample scenario

Create the sequence for client to back-end mediation as follows:

<sequence name="dispatchSeq" xmlns="http://ws.apache.org/ns/synapse">
    <property name="OUT_ONLY" value="true"/>
    <property name="websocket.accept.contenType" scope="axis2" value="application/json"/>
    <log level="full">
        <property name="LOGGED_MESSAGE" value="LOGGED"/>
    </log>
    <send>
        <endpoint>
            <address uri="ws://localhost:8082/websocket"/>
        </endpoint>
    </send>
</sequence>

Specify the websocket.accept.contenType property to inform the WebSocket sender to build the frames with the specified content type, and to include the same subprotocol header that was used to determine the content of the WebSocket frames. In this case it is JSON.

Create the sequence for back-end to client mediation as follows:

<sequence name="outDispatchSeq" trace="enable" xmlns="http://ws.apache.org/ns/synapse">
    <respond/>
    <log level="full"/>
</sequence>

Configure the WebSocket inbound endpoint in the ESB Profile of WSO2 EI as follows to use the created sequences and listen on port 9091:

<inboundEndpoint name="test" onError="fault" protocol="ws"
   	sequence="dispatchSeq" suspend="false">
   	<parameters>
       	<parameter name="inbound.ws.port">9091</parameter>
       	<parameter name="ws.outflow.dispatch.sequence">outDispatchSeq</parameter>
       	<parameter name="ws.client.side.broadcast.level">0</parameter>
       	<parameter name="ws.outflow.dispatch.fault.sequence">fault</parameter>
   	</parameters>
</inboundEndpoint>

Executing the sample scenario

Open a terminal, navigate to the location where you saved the netty artifacts, and execute the following command to start the WebSocket client:

java -DsubProtocol="synapse(contentType='application/json') -DclientPort=9091 -cp netty-example-4.0.30.Final.jar:lib/*:.io.netty.example.http.websocketx.client.WebSocketClient

You will see the following message on the client terminal:

WebSocket Client connected!

Send the following sample JSON payload from the client terminal:
```
("sample message":"test"}
```

Analyzing the output

When you send a sample JSON payload from the client, you will see that a connection from the WebSocket client to the ESB Profile of WSO2 EI is established, and that the ESB Profile of WSO2 EI receives the message. Following is the log that you will see:

This shows that the sequences are executed by the WebSocket inbound endpoint.

You will also see that the message sent to the WebSocket server is transformed, and that the response injected to the out sequence is also transformed.

Following is the server log that you will see:

Following is the client log that you will see: